Wrist Band Machine with Lamination and Die Cutting
Paper roll in, finished wristbands out, in one pass.
Three machines' work in a single pass
The Wrist Band Machine makes finished wristbands from a paper roll in a single pass. It unwinds the paper and the release paper on two separate stations, coats the release paper with hot melt glue through a slotter die, laminates the two webs together, die cuts the wristband shape on a rotary die, then carries the bands down a long conveyor to a collecting tray at the end.
Shops that make wristbands the usual way run three machines and handle the material three times: laminate, glue coat, die cut. This machine does all three in line, so a roll goes in one end and boxed-ready wristbands come off the other. Fewer handling steps means fewer registration errors, and one operator instead of three.
Both unwind stations take ø600 mm rolls on 3 inch air shafts and carry imported ultrasonic web guides. The paper side holds tension through an auto electronic tension controller with load cell feedback. The release paper side runs a powder brake with an amp meter, which lets the operator see the braking load rather than guess at it. The slotter die lays glue to the release paper width, so adhesive lands only where the band needs it.
Die cutting runs on a rotary unit with a nip roller and an 80 teeth magnet cylinder. The flexible die is made to your wristband design, so band length, punch holes, tear line and tab shape are yours rather than a fixed pattern. After the die there is a short conveyor and then a long conveyor with vacuum hold-down, which keeps light bands flat at speed and gives a mounting point for a batch coding unit if you number or date the bands.
Typical output goes to events, concerts, hospitals, water parks, resorts, clubs and entry management. Label converters add the machine as a new product line. New businesses buy it to produce and sell wristbands direct.
RK Label Printing Machinery Pvt. Ltd. has built label and packaging converting machines in Ahmedabad, Gujarat since 1995 and exports to 23+ countries including the USA, UAE, Japan, South Korea, Saudi Arabia and South Africa.
Key Features
Lamination, hot melt gluing and die cutting run inline, replacing three machines.
Separate ø600 mm unwinds for paper and release paper, each with its own guide.
Auto electronic tension control holds the web steady as the roll runs down.
The release paper operator reads the actual braking load instead of guessing.
The slotter die lays glue to the release paper width, so it goes only where it belongs.
Rotary die cutting with a nip roller for clean sheet cutting.
Holds light bands flat to the belt at speed instead of letting them lift.
The long conveyor is built to carry a batch coding unit for numbering or dating.
Three phase AC motor on a Schneider or Inovance drive for smooth speed control.
The flexible die is made to your wristband shape, not to a fixed house pattern.
Technical Specifications
- Machine Type
- Wristband making machine: one rotary die cutting unit with lamination unit, hot melt glue station and long conveyor
- Unwind, Paper Roll: Max Diameter
- ø600 mm
- Unwind, Paper Roll: Shaft
- 3 inch air shaft (75 mm)
- Unwind, Paper Roll: Web Guide
- Imported electronic ultrasonic web guide
- Unwind, Paper Roll: Tension
- Auto electronic tension controller with load cell feedback, imported
- Unwind, Release Paper: Max Diameter
- ø600 mm
- Unwind, Release Paper: Shaft
- 3 inch air shaft (75 mm)
- Unwind, Release Paper: Web Guide
- Imported electronic ultrasonic web guide
- Unwind, Release Paper: Tension
- Powder brake with amp meter
- Glue Station
- Hot melt, with slotter die sized to the release paper width
- Lamination Unit
- Sandwiches the paper with the hot melt coated release paper
- Die Cutting
- One rotary die cutting unit with nip roller for sheet cutting
- Magnet Cylinder
- 80 teeth
- Short Conveyor
- Immediately after the die cutting unit
- Long Conveyor
- Vacuum hold-down, with facility to mount a batch coding unit
- Collection
- Collecting tray at the end of the conveyor
- Main Motor
- 3 HP, three phase AC, variable speed control (VFD brand Schneider or Inovance)
- Priced Separately
- Batch coding printer; flexible die, made to the buyer's wristband design
- HSN / SAC
- 84431400
- Country of Manufacture
- India (Ahmedabad, Gujarat)
Gallery
Optional Add-ons
Configure the Wrist Band to your line — every machine is built to order.
Interested in the Wrist Band?
Tell us about your substrates, web width and colour requirements. Our team will respond with a tailored configuration and quote.
Frequently Asked Questions
Common questions about the Wrist Band and the other Wrist Band Machine machines.
It turns roll stock paper into finished laminated wristbands for events, concerts, hospitals, water parks, resorts, clubs and entry management. Lamination, hot melt gluing and die cutting all happen in one pass.